MSP430F249—SPI主從機通信

1。主機發送讀取

/******************************************************************
**
** File : SPI.c | Master Send |
** Version : 1.0
** Description: SPI Master Send and Receive
** Author : LightWu
** Date : 2013-4-16
**
*******************************************************************/


#include "MSP430x24x.h"


unsigned char Data1;




void Delay(void)
{
int m;
for(m=5000;m>0;m--);
}


void SpiInit(void)
{
P3SEL |= 0x0E; // P3.3,2,1 USCI_B0 option select,注意管腳配置
P3DIR |= 0x01; // P3.0 output direction
UCB0CTL0 |= UCCKPH + UCMSB + UCMST + UCSYNC; // 3-pin, 8-bit SPI mstr, MSB 1st
UCB0CTL1 |= UCSSEL_2; // SMCLK
UCB0BR0 = 0x02;
UCB0BR1 = 0;
UCB0CTL1 &= ~UCSWRST; // **Initialize USCI state machine**

IE2 |= UCB0RXIE; // 打開接收中斷
}






void main(void)
{
// Stop watchdog timer to prevent time out reset
WDTCTL = WDTPW + WDTHOLD; //關狗


SpiInit();


while(1)
{
//Data1 = TLC549Read();

//注意需要加延時
Delay();

P3OUT &= ~0x01; // Enable TLC549, /CS reset

UCB0TXBUF = 0x55; // Transmit first character


_BIS_SR(LPM0_bits + GIE); // CPU off, enable interrupts


}



}


#pragma vector=USCIAB0RX_VECTOR
__interrupt void USCIA0RX_ISR (void)
{
Data1 = UCB0RXBUF; // data = 00|DATA

P3OUT |= 0x01; // Disable TLC549, /CS set

__bic_SR_register_on_exit(LPM0_bits); // Exit LPM0
}

 

2.從機接收發送

/******************************************************************
**
** File : SPI.c | Slave Receive and Send |
** Version : 1.0
** Description: SPI Slave Receive and Send
** Author : LightWu
** Date : 2013-4-16
**
*******************************************************************/
#include




int main(void)
{
volatile unsigned int i;


WDTCTL = WDTPW+WDTHOLD; // Stop watchdog timer
// it is not yet in SPI mode
P3SEL |= 0x0E; // P3.3,2,1 option select
UCB0CTL1 = UCSWRST; // **Put state machine in reset**
UCB0CTL0 |= UCCKPH + UCSYNC+UCMSB; //3-pin, 8-bit SPI master
UCB0CTL1 &= ~UCSWRST; // **Initialize USCI state machine**
IE2 |= UCB0RXIE; // Enable USCI_B0 RX interrupt


_BIS_SR(LPM3_bits + GIE); // Enter LPM4, enable interrupts
}


// Echo character
#pragma vector=USCIAB0RX_VECTOR
__interrupt void USCIB0RX_ISR (void)
{
while (!(IFG2 & UCB0TXIFG)); // USCI_B0 TX buffer ready?
UCB0TXBUF = UCB0RXBUF;
}