24c02開機計數器程序

LED1EQU08H
LED2EQU09H
LED3EQU0AH
LED4EQU0BH

LedT0EQU0CH;0-3輪流點亮4個數據管

SDAEQUP2.0
SCLEQUP2.1
AddressEQU0EH
I2CDataEQU0FH
;=================================================
ORG0000H
LJMPSTART;轉入主程序

;=================================================
ORG000BH
;定時器0中斷入口
INT_TO:
PUSHACC
PUSHPSW

CLRTF0;清定時0中斷標志
MOV TH0,#0F6H;2.5MS
MOV TL0,#03DH;

MOV A,#11110000B;關數碼管
ORLP2,A

MOV A,LedT0
CJNEA,#0,INT_T0_1
MOV A,LED1
MOV CA,@A+DPTR
MOV P0,A
CLRP2.7
MOV LedT0,#1
LJMPINT_T0_END
INT_T0_1:

MOV A,LedT0
CJNEA,#1,INT_T0_2
MOV A,LED2
MOV CA,@A+DPTR
MOV P0,A
CLRP2.6
MOV LedT0,#2
LJMPINT_T0_END
INT_T0_2:

MOV A,LedT0
CJNEA,#2,INT_T0_3
MOV A,LED3
MOV CA,@A+DPTR
MOV P0,A
CLRP2.5
MOV LedT0,#3
LJMPINT_T0_END
INT_T0_3:

MOV A,LED4
MOV CA,@A+DPTR
MOV P0,A
CLRP2.4
MOV LedT0,#0
LJMPINT_T0_END

INT_T0_END:

POPPSW
POPACC

RETI

;=============================================

START:
MOV SP,#60H

CALLDELAY10MS
CALLDELAY10MS
CALLDELAY10MS

CALLAT24C01_READ_ALL

MOV A,LED1
CJNEA,#10,$+3;A<10,C=1
JNCSTART_RESET_24C01
MOV A,LED2
CJNEA,#10,$+3;A<10,C=1
JNCSTART_RESET_24C01
MOV A,LED3
CJNEA,#10,$+3;A<10,C=1
JNCSTART_RESET_24C01
MOV A,LED4
CJNEA,#10,$+3;A<10,C=1
JNCSTART_RESET_24C01
JMPSTART_INC
;第一次使用復位內部數值
START_RESET_24C01:
MOV LED1,#0
MOV LED2,#0
MOV LED3,#0
MOV LED4,#0
JMPSTART_INC_END
;加1
START_INC:
INCLED4
MOV A,LED4
CJNEA,#10,START_INC_END;等于10，進位
MOV LED4,#00
INCLED3
MOV A,LED3
CJNEA,#10,START_INC_END
MOV LED3,#00
INCLED2
MOV A,LED2
CJNEA,#10,START_INC_END
MOV LED2,#00
INCLED1
MOV A,LED1
CJNEA,#10,START_INC_END
MOV LED1,#00
MOV LED2,#00
MOV LED3,#00
MOV LED4,#00

START_INC_END:
;儲存
CALLAT24C01_WRITE_ALL


MOV TMOD,#01H;設定T0為十六位定時模式。
MOV TH0,#0F6H;2MS
MOV TL0,#03DH;
SETBTR0;開定時器0
SETBET0;致能定時0中斷
CLRTF0;清定時0中斷標志
SETBEA;開總中斷

MOV LedT0,#00H
MOV DPTR,#TABLE


;=============================================
SCAN:

;按鍵掃描
JBP3.2,$
LCALLDELAY10MS;去抖動
JNBP3.2,KEY_RESET
LJMPSCAN
;=============================================
KEY_RESET:
MOV LED1,#00
MOV LED2,#00
MOV LED3,#00
MOV LED4,#00

;儲存
CALLAT24C01_WRITE_ALL
;檢測按鍵是否放開
JNBP3.2,$
JMPSCAN

DELAY10MS:
MOV R4,#20
DELAY10MSA:
MOV R5,#247
DJNZR5,$
DJNZR4,DELAY10MSA
RET

TABLE:
DB00101000B;0
DB11101011B;1
DB00110010B;2
DB10100010B;3
DB11100001B;4
DB10100100B;5
DB00100100B;6
DB11101010B;7
DB00100000B;8
DB10100000B;9
DB01100000B;A
DB00100101B;b
DB00111100B;C
DB00100011B;d
DB00110100B;E
DB01110100B;F
DB11110111B;-
DB11111111B;
;====================================================
;讀出全部數據
AT24C01_READ_ALL:
MOV Address,#00H
CALLI2C_READ
MOV LED1,A;讀出數據
MOV Address,#01H
CALLI2C_READ
MOV LED2,A;讀出數據
MOV Address,#02H
CALLI2C_READ
MOV LED3,A;讀出數據
MOV Address,#03H
CALLI2C_READ
MOV LED4,A;讀出數據
RET
;====================================================
;寫入全部數據
AT24C01_WRITE_ALL:
MOV Address,#00H
MOV A,LED1
MOV I2CData,A
CALLI2C_WRITE;寫入數據
MOV Address,#01H
MOV A,LED2
MOV I2CData,A
CALLI2C_WRITE;寫入數據
MOV Address,#02H
MOV A,LED3
MOV I2CData,A
CALLI2C_WRITE;寫入數據
MOV Address,#03H
MOV A,LED4
MOV I2CData,A
CALLI2C_WRITE;寫入數據
RET
;====================================================
;寫一個字節Address地址I2CDatata寫入的數據
;====================================================
I2C_WRITE:
I2C_WRITE_A:
LCALLI2C_START
MOV A,#10100000B
LCALLI2C_SEND8BIT
LCALLI2C_ACK
JCI2C_WRITE_A;=1，表示無確認，再次發送

MOV A,Address
LCALLI2C_SEND8BIT
LCALLI2C_ACK

MOV A,I2CData
LCALLI2C_SEND8BIT
LCALLI2C_ACK
LCALLI2C_STOP
RET



;====================================================
;讀一個字節Address地址Data讀出的數據
;====================================================

I2C_READ:
I2C_READ_A:
LCALLI2C_START
MOV A,#10100000B
LCALLI2C_SEND8BIT
LCALLI2C_ACK
JCI2C_READ_A;=1，表示無確認，再次發送

MOV A,Address
LCALLI2C_SEND8BIT
LCALLI2C_ACK

I2C_READ_B:
LCALLI2C_START
MOV A,#10100001B
LCALLI2C_SEND8BIT
LCALLI2C_ACK
JCI2C_READ_B

LCALLI2C_RECEIVE8BIT
MOV I2CData,A
LCALLI2C_ACK
LCALLI2C_STOP
RET



;發送開始信號
I2C_START:
SETBSCL
SETBSDA
NOP
NOP
CLRSDA
NOP
NOP
CLRSCL
RET
;發送結束信號
I2C_STOP:
CLRSDA
NOP
NOP
SETBSCL
NOP
NOP
SETBSDA
RET

;發送接收確認信號
I2C_ACk:
SETBSDA
SETBSCL
NOP
NOP
JBSDA,I2C_ACK0
CLRC
SJMPI2C_ACK_END
I2C_ACK0:
SETBC
I2C_ACK_END:
CLRSCL
RET

;送八位數據
I2C_SEND8BIT:
MOV B,#08H
I2C_SEND8BIT_A:
RLCA

MOV SDA,C
SETBSCL
NOP
NOP
CLRSCL
DJNZB,I2C_SEND8BIT_A
RET


;接收八位數據
I2C_RECEIVE8BIT:
MOV B,#08H
CLRA
SETBSDA
I2C_RECEIVE8IT_A:
SETBSCL
NOP
NOP
MOV C,SDA
RLCA
CLRSCL
DJNZB,I2C_RECEIVE8IT_A

RET
END