IGLOO的FPGA構成的馬達控制方案

本文介紹了IGLOO系列主要特性和優勢，IGLOO系列架構框圖以及采用AGL125的馬達控制子板主要特性，步進馬達控制邏輯方框圖，BLDC馬達控制邏輯方框圖以及馬達控制子板電路圖和材料清單。

Actel公司的IGLOO系列FPGA是采用Flash Freeze技術的低功耗閃存FPGA，它基于130nm閃存工藝，具有最低功耗，單片解決方案和小占位面積的封裝，可重新編程以及豐富的其它特性，核電壓1.2 V -1.5 V，支持低功耗和單電壓系統工作，F(xiàn)lash Freeze模式的功耗為5uW，系統門從15K到100萬，多達144kb的雙端口SRAM和多達300個用戶I/O，可滿足消費品，工業，醫療，汽車電子，計算，通信和軍用航天領域的便攜產品對低功耗的需要。

IGLOO系列主要特性和優勢：

Low Power

• 1.2 V to 1.5 V Core Voltage Support for Low Power

• Supports Single-Voltage System Operation

• 5 μW Power Consumption in Flash*Freeze Mode

• Low Power Active FPGA Operation

• Flash*Freeze Technology Enables Ultra-Low Power Consumption while Maintaining FPGA Content

• Easy Entry to / Exit from Ultra-Low Power Flash*Freeze Mode

High Capacity

• 15 k to 1 Million System Gates

• Up to 144 kbits of True Dual-Port SRAM

• Up to 300 User I/Os

Reprogrammable Flash Technology

• 130-nm, 7-Layer Metal, Flash-Based CMOS Process

• Live-at-Power-Up (LAPU) Level 0 Support

• Single-Chip Solution

• Retains Programmed Design When Powered Off

• 250 MHz (1.5 V systems) and 160 MHz (1.2 V systems) System Performance

In-System Programming (ISP) and Security

• Secure ISP Using On-Chip 128-Bit Advanced Encryption Standard (AES) Decryption (except ARM®-enabled IGLOO® devices) via JTAG (IEEE 1532–compliant)†

• FlashLock® to Secure FPGA Contents

High-Performance Routing Hierarchy

• Segmented, Hierarchical Routing and Clock Structure

Advanced I/O

• 700 Mbps DDR, LVDS-Capable I/Os (AGL250 and above)

• 1.2 V, 1.5 V, 1.8 V, 2.5 V, and 3.3 V Mixed-Voltage Operation

• Bank-Selectable I/O Voltages—up to 4 Banks per Chip

• Single-Ended I/O Standards: LVTTL, LVCMOS 3.3 V / 2.5 V / 1.8 V / 1.5 V / 1.2 V, 3.3 V PCI / 3.3 V PCI-X,and LVCMOS 2.5 V / 5.0 V Input†

• Differential I/O Standards: LVPECL, LVDS, B-LVDS, and MLVDS (AGL250 and above)

• Wide Range Power Supply Voltage Support per JESD8-B, Allowing I/Os to Operate from 2.7 V to 3.6 V

• Wide Range Power Supply Voltage Support per JESD8-12, Allowing I/Os to Operate from 1.14 V to 1.575 V

• I/O Registers on Input, Output, and Enable Paths

• Hot-Swappable and Cold-Sparing I/Os‡

• Programmable Output Slew Rate† and Drive Strength

• Weak Pull-Up/-Down

• IEEE 1149.1 (JTAG) Boundary Scan Test

• Pin-Compatible Packages across the IGLOO Family

Clock Conditioning Circuit (CCC) and PLL†

• Six CCC Blocks, One with an Integrated PLL

• Configurable Phase Shift, Multiply/Divide, Delay Capabilities, and External Feedback

• Wide Input Frequency Range (1.5 MHz up to 250 MHz)

Embedded Memory

• 1 kbit of FlashROM User Nonvolatile Memory

• SRAMs and FIFOs with Variable-Aspect-Ratio 4,608-Bit† RAM Blocks (×1, ×2, ×4, ×9, and ×18 organizations)

• True Dual-Port SRAM (except ×18)†

ARM Processor Support in IGLOO FPGAs

• M1 IGLOO Devices—Cortex™-M1 Soft Processor Available with or without Debug


圖1。IGLOO系列架構框圖（AGL015, AGL030, AGL060和AGL125)

馬達控制子板

The Motor Control daughtercard provides a design reference and evaluation kit for motor control using Actel’s ultra-low power IGLOO® FPGAs. This daughtercard, co-developed with Actel and Ishnatek, is available exclusively from Avnet Memec. The board is designed to work with Actel’s IGLOO Icicle™ Kit (ordered separately) and attaches to the Icicle kit’s accessory board edge connector.

馬達控制子板主要特性：

• Supports

Stepper Motor (4-Wire Configuration)

Full Step / Half Step Mode

Micro Step Mode (Trapezoidal Option)

8 / 16 Microsteps

Brushless DC (BLDC) Motor (Three Phase BLDC Motor)

Sensored Drive

• Using Hall Effect Sensors provided on Motors

• Direction Control – Clockwise or Counterclockwise Rotation

• Basic Functions

Start

Stop

Step ( Full or Half Stepping in case of Stepper Motor)

RPM+/RPM- (Increase/Decrease RPM)

Digital Control Features

• Support Two PWM Modes

PWM on high side of Mosfet Bridge

PWM on low side of Mosfet Bridge (Available but not supported)

• Hardware/Software Control

Access to all above features through keys/switches on board

Equivalent controls are provided also through software

Software Interface using on-board USB-to-RS232 bridge on Icicle

• High Output Current up to 2 A

圖2。馬達控制子板外形圖

圖3。步進馬達控制邏輯方框圖

圖4。BLDC馬達控制邏輯方框圖

圖5。馬達控制子板電路圖（1）

圖6。馬達控制子板電路圖（2）

圖7。馬達控制子板電路圖（3）
馬達控制子板材料清單（BOM）：