上位機控制單片機LED

整了一天程序，寫了個上位機程序和單片機程序?？偨Y(jié)下。。。

上位機部分：

相關參考資料：http://wenku.baidu.com/view/5ea8670403d8ce2f00662322.html

1.先添加各控件，添加后的對話框如下圖：

2.再添加對應的成員變量。

3.最后添加函數（事件處理函數）。

3.1初始化，設置串口各參數。

BOOLCLedControlDlg::OnInitDialog(){CDialog::OnInitDialog();// 設置此對話框的圖標。當應用程序主窗口不是對話框時，框架將自動// 執行此操作SetIcon(m_hIcon, TRUE); // 設置大圖標SetIcon(m_hIcon, FALSE); // 設置小圖標// TODO: 在此添加額外的初始化代碼m_ctrlComm.put__CommPort(5); //選擇com3m_ctrlComm.put_InputMode(1); //以二進制方式輸入m_ctrlComm.put_InBufferSize(1024);m_ctrlComm.put_OutBufferSize(512);//設置串口,波特率115200，無校驗位，數據位8，停止位1m_ctrlComm.put_Settings(_T("115200,n,8,1"));//參數1表示當接受緩沖區有多于等于1個字符//引發OnCommm_ctrlComm.put_RThreshold(1);if(!m_ctrlComm.get_PortOpen()){m_ctrlComm.put_PortOpen(TRUE);//打開串口}m_ctrlComm.put_InputLen(0); //設置當前緩沖區為0m_ctrlComm.get_Input(); //先預讀緩沖區returnTRUE; // 除非將焦點設置到控件，否則返回 TRUE}

3.2處理串口發來的數據。

voidCLedControlDlg::OnComm(){// TODO: 在此處添加消息處理程序代碼VARIANT variant_inp;COleSafeArray safearray_inp;LONGlen,k;BYTErxdata[2048]; //設置BYTE數組 An 8-bit integerthat is not signed.CString strtemp;if(m_ctrlComm.get_CommEvent()==2) //事件值為2表示接收緩沖區內有字符{ ////////以下你可以根據自己的通信協議加入處理代碼variant_inp=m_ctrlComm.get_Input(); //讀緩沖區safearray_inp=variant_inp; //VARIANT型變量轉換為ColeSafeArray型變量len=safearray_inp.GetOneDimSize(); //得到有效數據長度for(k=0;k　3.3串口發送數據出去。

voidCLedControlDlg::OnButtonManualsend(){// TODO: 在此添加控件通知處理程序代碼UpdateData(true);m_ctrlComm.put_Output(COleVariant(m_strEditTXData));UpdateData(false);}

單片機部分：

#include #include #include #include //標準函數#include //I/O口函數#define _Nop() _nop_()#define uchar unsigned char#define uint unsigned int#define LEDCTL0Low P4&=~0x01;#define LEDCTL0High P4|=0x01;#define LEDCTL1Low P4&=~0x02;#define LEDCTL1High P4|=0x02;#define LEDCTL2Low P4&=~0x04;#define LEDCTL2High P4|=0x04;#define LEDCTL3Low P4&=~0x08;#define LEDCTL3High P4|=0x08;//--------------------------------------------------------------------// 全局常量//--------------------------------------------------------------------#define SYSCLK 22118400 // SYSCLK frequency in Hz#define BAUDRATE 115200 // Baud rate of UART in bps#define MAX_LEN 50 //receive buf MAX lengthuchar readCounts;uchar trdata[MAX_LEN] = {'0', '0', '0', '0'}; //四個LED數碼管初始顯示都為0uchar sendlen;uchar message[]="Receive Buf is full";bit readFlag;bit frameFlag;chardata SFRPAGE_SAVE;uchar code LEDSEG1[]= {0xC0,0xF9,0xA4,0xB0,0x99,0x92,0x82,0xF8,0x80,0x90,0xc6,0X89};//0~9,C,H,正uchar code LEDSEG2[]= {0xC0,0xCF,0xA4,0x86,0x8B,0x92,0x90,0xC7,0x80,0x82,0xF0,0X89};//0~9,C,H,倒//--------------------------------------------------------------------//函數聲明//--------------------------------------------------------------------voidSYSCLK_Init (void);voidPORT_Init(void);voidUART0_Init(void) ;voidSend_Char(uchar ch) ;voidsend_string_com(unsigned char*str,unsigned intstrlen);voiddisplay(unsigned char*str);voidDelay(uint tt);//--------------------------------------------------------------------// 主函數//--------------------------------------------------------------------voidmain (void){WDTCN = 0xde;WDTCN = 0xad; //關閉WDTSYSCLK_Init ();PORT_Init();UART0_Init();EA=1;ES0=1;SFRPAGE = LEGACY_PAGE;while(1){if(frameFlag){frameFlag=0;send_string_com(trdata,sendlen);}display(trdata);}}//-----------------------------------------------------------------------------// 系統時鐘配置//-----------------------------------------------------------------------------voidSYSCLK_Init (void){inti = 0;//char SFRPAGE_SAVE = SFRPAGE; // Save Current SFR pageSFRPAGE = CONFIG_PAGE; // set SFR pageOSCXCN = 0x67; // start external oscillator with// 22.1184MHz crystalfor(i=0; i < 3000; i++) ; // XTLVLD blanking interval (>1ms)while(!(OSCXCN & 0x80)) ; // Wait for crystal osc. to settleCLKSEL = 0x01; //SYSCLK derived from the External Oscillator circuitOSCICN &= ~0x80; //Internal Oscillator Disabled}//-----------------------------------------------------------------------------// I/O配置//-----------------------------------------------------------------------------voidPORT_Init(){ SFRPAGE = CONFIG_PAGE; // set SFR page before writing